Logo
Login Sign Up
Current Revision

ASTM D1675-18

Standard Test Methods for Polytetrafluoroethylene Tubing
Best Price Guarantee
Instant
2-5 Days
SAVE 10%

$69.00

$69.00

$124.20

$83.00

$83.00

$149.40



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


View in Library
or
...

1.1 These test methods cover procedures for testing polytetrafluoroethylene tubing for use as electrical insulation. The procedures appear in the following sections:

Procedure

  • Conditioning — Sections 7 — ASTM Methods ...
  • Dielectric Breakdown Voltage — Sections 28 – 30 — ASTM Methods D149, D876
  • Inside Diameter — Sections 8 – 13 — ASTM Method D876
  • Mandrel Bend Test — Sections 46 – 52 — ASTM Methods D149, D876
  • Melting Point — Sections 41 – 45 — ASTM Methods D3418, D4895
  • Penetration Test — Sections 26 and 27 — ASTM Method D876
  • Specific Gravity — Sections 36 – 40 — ASTM Methods D792, D1505
  • Strain Relief — Sections 31 – 35 — ASTM Methods ...
  • Volatile Loss — Sections 20 – 25 — ASTM Methods ...
  • Wall Thickness — Sections 14 – 19 — ASTM Methods ...

Note 1: These test methods are similar but not identical to those in IEC 60684–2.

1.2 The values stated in inch-pound units are the standard except for temperature, which is stated in degrees Celsius. Values in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 5.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

1.1 These test methods cover procedures for testing polytetrafluoroethylene tubing for use as electrical insulation.

The procedures appear in the following sections:

 
  Procedure

 
Sections

  ASTM Methods

 

 

 

Conditioning

 7

...

Dielectric Breakdown Voltage

28 – 30

D149, D876

Inside Diameter

 8 – 13

D876

Mandrel Bend Test

46 – 52

D149, D876

Melting Point

41 – 45

D3418, D4895

Penetration Test

26 and 27

D876

Specific Gravity

36 – 40

D792, D1505

Strain Relief

31 – 35

...

Volatile Loss

20 – 25

...

Wall Thickness

14 – 19

...

Note 1: These test methods are similar but not identical to those in IEC 60684–2.

1.2 The values stated in inch-pound units are the standard except for temperature, which is stated in degrees Celsius. Values in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 5.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International

4.1 The test methods in this standard are considered important to characterize polytetrafluoroethylene tubing. They are intended primarily for, but not limited to polytetrafluoroethylene tubing.

4.2 Variations in these methods or alternate contemporary methods of measurement may be used to determine the values for the properties in this standard provided such methods ensure quality levels and measurement accuracy equal to or better than those prescribed herein. It is the responsibility of the organizations using alternate test methods to be able to demonstrate this condition. In cases of dispute, the methods specified herein shall be used.

Note 2: Provision for alternate methods is necessary because of:

  • the desire to simplify procedures for specific applications, and
  • the desire to eliminate redundant testing and use data generated during manufacturing process control, including that generated under Statistical Process Control (SPC) conditions, using equipment and methods other than those specified herein.

An example would be the use of laser micrometers or optical comparators to measure dimensions.

SDO ASTM: ASTM International
Document Number D1675
Publication Date May 1, 2018
Language en - English
Page Count 6
Revision Level 18
Supercedes
Committee D09.07
Loading...

Failed to load document history.

Publish Date Document Id Type View