Current Revision

BSI BS EN 1253-6:2022

Gullies for buildings -- Trapped floor gullies with a depth of water seal less than 50 mm

Online PDF

$310.76

Bundle

$559.37

Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00

I have read and agree to the Terms & Conditions

BSI BS EN 1253-6:2022

Gullies for buildings -- Trapped floor gullies with a depth of water seal less than 50 mm

PUBLISH DATE 2022

PAGES 32

Document Information

This document classifies floor gullies for domestic waste water for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with a depth of water seal less than 50 mm (referred to as floor gullies). NOTE Floor gullies with a depth of water seal less than 50 mm are not covered by EN 1253 1, EN 1253 7 and EN 1253 8. These products are intended to be installed where the three following conditions are met: - space limitation will not accommodate a gully with a 50 mm water seal; - the building does not exceed a ground-floor and three floors above; - at least two domestic sanitary appliances are installed in addition to the gully but with only one WC on the same branch (connection pipe) or secondary or branch ventilation is installed (see EN 12056 2:2000, 4.3.2 or 4.3.4.


SDO	BSI: British Standards Institution
Document Number	EN 1253-6
Publication Date	Nov. 1, 2022
Language	en - English
Page Count	32
Revision Level
Supercedes
Committee	B/505/11

Publish Date	Document Id	Type	View
Nov. 1, 2022	BS EN 1253-6:2022	Revision

SDO	Document	Title
BSI	BSI BS EN 1253-1	Gullies for buildings -- Trapped floor gullies with a depth water seal of at least 50 mm
BSI	BSI BS EN 1253-8	Gullies for buildings -- Trapped floor gullies with combined mechanical closure and water seal
BSI	BSI BS EN 1253-7	Gullies for buildings -- Trapped floor gullies with mechanical closure
BSI	BSI BS EN 1253-2	Gullies for buildings -- Roof drains and floor gullies without trap
BSI	BSI BS EN 3480	Aerospace series. Steel X6CrNiTi18-10 (1.4541). Air melted. Softened. Plates. 6 mm &lt; a = 50 mm. 500 MPa = R<sub>m</sub> = 700 MPa Aerospace series. Steel X6CrNiTi18-10 (1.4541). Air melted. Softened. Plates. 6 mm &lt; a = 50 mm. 500 MPa = R<sub>m</sub> = 700 MPa Aerospace series. Steel X6CrNiTi18-10 (1.4541). Air melted. Softened. Plates. 6 mm &lt; a = 50 mm. 500 MPa = R<sub>m</sub> = 700 MPa
BSI	BSI BS 18-3	Methods for tensile testing of metals -- Steel sheet and strip (less than 3 mm and not less than 0.5 mm thick)
AWWA	AWWA C907	Injection-Molded Polyvinyl Chloride (PVC) Pressure Fittings, 4 In. Through 12 In. (100 mm Through 300 mm), for Water, Wastewater, and Reclaimed Water Service
AWWA	AWWA C228	Stainless-Steel Pipe Flange Joints for Water Service--Sizes 2 In. Through 72 In. (50 mm Through 1800 mm)
BSI	BSI BS 4735	Laboratory method of test for assessment of the horizontal burning characteristics of specimens no larger than 150 mm x 50 mm x 13 mm (nominal) of cellular plastics and cellular rubber materials when subjected to a small flame
ISO	ISO 4586-5	High-pressure decorative laminates (HPL, HPDL) - Sheets based on thermosetting resins (usually called laminates) - Part 5: Classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates
BSI	BSI BS EN 438-5	High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) -- Classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates
BSI	BSI BS ISO 4586-5	High-pressure decorative laminates (HPL, HPDL). Sheets based on thermosetting resins (usually called laminates) -- Classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates
IEC	IEC 60191-6-2	Mechanical standardization of semiconductor devices - Part 6-2: General rules for the preparation of outline drawings of surface mounted semiconductor devices packages - Design guide for 1,50 mm, 1,27 mm and 1,00 mm pitch ball and column terminal packages
BSI	BSI BS EN 60191-6-2	Mechanical standardization of semiconductor devices. General rules for the preparation of outline drawings of surface mounted semiconductor device packages -- Design guide for 1,50 mm, 1,27 mm and 1,00 mm pitch ball and column terminal packages
BSI	BSI BS EN 681-4	Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications -- Cast polyurethane sealing elements
BSI	BSI BS EN 1253-5	Gullies for buildings -- Gullies with light liquids closure
BSI	BSI BS EN 2045	Aerospace series. Square bars, drawn, in aluminium and aluminium alloys. Tolerance class h 11. Thickness 6 mm ≤ a ≤ 50 mm. Dimensions
BSI	BSI BS EN 4209	Aerospace series. Aluminium alloy AL-P2219-T851. Plate. 6 mm <a ≤50 mm
BSI	BSI BS EN 4575	Aerospace series. Heat resisting alloy X12CrNiCoMoW21-20. Solution treated and descaled. Sheets and plates. 3 mm < a ≤ 50 mm
BSI	BSI BS EN 2046	Hexagonal bars, drawn, in aluminium and aluminium alloys. Tolerance class h 11. Width across flats 7 mm ≤ a ≤ 50 mm. Dimensions
BSI	BSI BS EN 2960	Aerospace series. Heat resisting nickel base alloy (NI- P101HT). Cold worked and solution treated. Bars for machining for fasteners. 3 mm ≤ D ≤ 50 mm
BSI	BSI BS EN 4890	Aerospace series. Steel X4CrNiMo16-5-1. Air melted. Hardened and tempered. Sheets and plates. 0,3 mm ≤ a ≤ 50 mm. 900 MPa ≤ Rm ≤ 1 050 MPa
BSI	BSI BS EN 4642	Aerospace series. Steel FE-PM 3504 (X4CrNiMo16-5-1). Air melted. Hardened and tempered. Sheet and plate. 0,6 mm ≤ a ≤ 50 mm. 900 MPa ≤ Rm ≤ 1050 MPa
BSI	BSI BS EN 3459	Aerospace series. Titanium alloy TI-P63001 (Ti-4Al-4Mo-2Sn). Solution treated and aged. Plate. 6 mm < a ≤ 50 mm
BSI	BSI BS EN 2699	Aerospace series. Aluminium alloy (5086). Annealed and straightened (H111). Drawn bar. 6 mm ≤ D ≤ 50 mm